# B Power Tools

> From first pilot hole to clean drive

## Articles

- [Wyze Camera Recall: Wrong Screw Length Explained](https://www.bpowertools.com/blog/wyze-camera-recall-wrong-screw-length): See which Wyze Solar Cam Pan installations are recalled, why the long screw can reach the battery, and how to check clearance before mounting.
- [Can Deck Screws Be Used in Joist Hangers? No](https://www.bpowertools.com/blog/can-deck-screws-be-used-in-joist-hangers): Ordinary deck screws do not replace joist-hanger fasteners. Learn how to verify approved nails or connector screws, patterns, loads, and coatings.
- [FLEX FX1372 vs FX1371 Impact Driver: Upgrade or Keep?](https://www.bpowertools.com/blog/flex-fx1372-vs-fx1371-impact-driver): Compare FLEX FX1372 and FX1371 torque, speed, weight, size, collets, kits, and test times to see whether the newer impact driver earns an upgrade.
- [Is DeWalt Powerstack Discontinued? XR Battery Guide](https://www.bpowertools.com/blog/is-dewalt-powerstack-discontinued): DeWalt retired the Powerstack label, not every pouch-cell pack. Match DCBP034, DCBP320, DCBP520, DCB2105 and DCB2108 to your tool and job.
- [Phillips Truss Head Refers to Two Screw Features](https://www.bpowertools.com/blog/phillips-truss-head-screw): Phillips identifies the drive recess, while truss identifies the broad, non-countersunk head. Those terms alone do not prove two screws are interchangeable.
- [#14 Screw Dimensions Vary by Type](https://www.bpowertools.com/blog/14-screw-dimensions): One production wood-screw guide puts thread diameter at 0.235-0.246 in. and body diameter at 0.190-0.201 in., showing why measurement point matters.
- [Choose and Fit a Countersunk Flat-Head Screw](https://www.bpowertools.com/blog/countersunk-flat-head-screw): For a reliable flush fit, define the installed height, use the selected screw's drawing, match the countersink and test a representative sample.
- [View the Drill Bit Sizes Chart](https://www.bpowertools.com/blog/drill-bit-sizes-chart): Fractional, metric, number and letter entries appear in diameter order. In the #80-to-#1 series, diameter grows as the designation number decreases.
- [Brass Screws Have Clear Uses and Limits](https://www.bpowertools.com/blog/brass-screws): Brass has roughly one-third to half the tensile strength of steel, and the head can twist off abruptly, leaving a soft shank that extractors struggle to grip.
- [Impact Wrench vs Impact Driver: Fastener Type Decides](https://www.bpowertools.com/blog/impact-wrench-vs-impact-driver): Screws favor a driver and sockets favor a wrench. A driver may still be enough when socket work is occasional, accessible, and light.

## Pages

- [About B Power Tools](https://www.bpowertools.com/about): How B Power Tools researches fastener, bit, and driver references.
- [Fastener Tool Matching Starts at the Head](https://www.bpowertools.com/fastener-tool-matcher): Fit the bit fully to the recess before choosing a driver for size and material. If it rocks, bottoms out early or only touches at the tips, stop.
- [What Is the Learning Path for Working With Fasteners?](https://www.bpowertools.com/learning-path): The route starts with the staged board on the homepage. The matcher comes next once you have a specific fastener in hand.
- [Contact](https://www.bpowertools.com/contact): 
- [Privacy Policy](https://www.bpowertools.com/privacy): 
- [Terms & Conditions](https://www.bpowertools.com/terms):